ESky A Tx, A and Gyro Guide: A guide to the standard radio control gear that comes with the ESky King/King 2 and Belt-CP. ESky Transmitter . Esky a 6 channel transmitter manual. Link: Download Esky a 6 channel transmitter manual. Information: Date added: Downloads: Filename: esky a 6 channel transmitter manual. Date: 15/10/ Type of compression: zip. Total downloads: Nick: fraccer. File checked: Kaspersky.
|Published (Last):||14 October 2017|
|PDF File Size:||18.79 Mb|
|ePub File Size:||20.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.
Numbers on the Picture in each section Corresponds to the descriptions below it.
Rear Side of the Transmitter: Here is the TOP of the Transmitter: Push it Up to make the Elevator tilt forward and Down. Pull it back to make manuak Elevator tilt kanual and Down. Move it Left to make the Aileron tilt left move Left, Sideways flight and right to tilt right move Right, Sideways flight.
Last edited by Finless; at Switches inside battery compartment: Mode 1 is A down, B up. Mode 2 is both switches down.
ESky 0406A Tx, 0420A and 0704 Gyro Guide:
Originally Posted by DierWolf. Left Portion of Transmitter: Cant edit the post now that it became a sticky For anyone reading please take note of above comment.
I wasn’t able to change the mode of my tx using the two dip switches, any clues? Originally Posted by tomgj. Didn’t really take the time to play with the heli with the different switch settings, but when I get more time I will give a few combinations ago. Also the motor was disconnected.
I’m thinking I may just have to get used to mode 1, as both my tx units and my sim are mode 1, oh well! Does anyone know how to correctly eky up trainer mode using two TX’s. Don’t quote me on this but I think you must mnaual the crystal from Tx 1 The NOOBIE and the trainer switch is held by Tx 2 the one who has the skills to pilot the bird and must be held to give control to Tx 1.
When the trainer switch is not held by Tx 2, Tx 2 has full control of the heli. Thanks, just what I was looking for! Originally Manal by fluffhead. When you switch to 90 degree swash you lose idle up. Is there a way to keep idle up and 90 deg swash?
What do you mean there’s no idle up with a 90 deg swash? That’s FP mode with no pitch aileron and elevator onlyso all you get is high RPM at all throttle stick positions.
Download esky a 6 channel transmitter manual | Diigo Groups
If I recall correctly, it does still work although it obviously doesn’t do anything useful. The right pit knob works as a fifth channel in Phoenix.
I had it set to idle up but found i just leave it on anyway. So I switched it back to keyboard and use controller knob for throttle hold for autos. Hello, i have the EK2 – lama transmitter, i want to use for a plane, how its the setup of the switchs??? Originally Posted by pipe I try, but the trotthle not works, I have a esky receiver ek, the esc in ch3, servos work, but the motor no.
Was that a “receiver ready” plane, or did you set up the ESC and motor yourself?
If so, what are they? The receiver is getting power so the connection between the receiver and ESC is good Now you just need to figure out why the motor isn’t responding. Do you get any arming beeps from the motor when the ESC powers up? Sorry for my bad english, Im from Chile. Please click one of the Quick Reply icons in the posts above to activate Quick Reply. Quote message in reply? In order to be able to post messages on the HeliFreak forums, you must first register.
Posting Quick Reply – Please Wait. Page 1 of 3. Remove Advertisements Sponsored Links.
E SKY EKA INSTRUCTION MANUAL Pdf Download.
Originally Posted by tomgj I wasn’t able to change the mode of my tx using the two dip switches, any clues? Originally Posted by tomgj I’m thinking I may just have to get used to mode 1, as both my tx units and my sim are mode 1, oh well! Originally Posted by fluffhead Can you elaborate?
Originally Posted by pipe09 Hello, i have the EK2 – lama transmitter, i want to use for a plane, kanual its the setup of the switchs???
E Sky EK2-0406A Instruction Manual
Options Quote message in reply? Register Now In order to be able ,anual post messages on the HeliFreak forums, you must first register.
Password Please enter a password for your user account. Note that passwords are case-sensitive. Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site.